Beginner's Plumbing: The Essentials for Installing a Bathtub
Beginner's Plumbing: The Essentials for Installing a Bathtub
Blog Article
Here in the next paragraph you can locate additional brilliant data pertaining to How to Install a Bathtub Yourself.
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably hard job. If the old tub is readily available, the job can relocate quickly; if you need to open up a wall surface to eliminate the old tub and place the new bathtub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and embeded in the new one. Make sure you have actually qualified on your own for the work and also fit trying it. Rather than working with a specialist to take over a halfway-completed job, it is better to think about utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will help you mount a brand-new bath tub in your bathroom if you have currently purchased a new tub and don't need to alter the setup of your previous supply of water pipes.
Your devices as well as product list must comprise the following:
Preparing for the Installment
To start with, the supporting framework provided with the bathroom must be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must now be ready to be suited its final placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, put the bathtub in the required position. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub up until the spirit level reads level.
To mount faucets, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water supply and also examine all joints as well as new pipework for leakages and also tighten them if essential. Fill up the bathtub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been utilized a minimum of when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in location in between the tap and the sink. Protect the faucet in position with the maker offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former kind should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a rigid seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, leading to difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealant can crack rather early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that review on A Step-by-Step Guide to Installing a Bathtub while doing a search on the internet. Please set aside a second to share this content if you liked it. I am grateful for your time. Visit us again soon.
Trusted service? Dial! Report this page